9. UART¶

9.1. Introduction¶

ROC-RK3568-PC-SE supports UART、RS232、RS485 interfaces. They are UART7, two RS232 and one RS485, which are located on the dual expansion interface and RJ45 interface respectively. The serial port interface diagram is as follows:

_images/uart_interface.jpg

Note: In this chapter, two RS232 will be defined as RS232_1、RS232_2, which is used to explains how to use UART.

9.2. Pin definition¶

9.2.1. UART7¶

TX and RX of UART7 are multiplexed. Actually，UART7 TX and UART7 RX correspond to the silk screen printing PWM14 and SPDIF on the development board respectively. UART9 is turned on by default in the public firmware. If you want to using other functions, UART9 needs to be turned off first. The details is follow:

func0	func1	func2	func3	func4	func5
GPIO3_C4	PWM14_M0	VOP_PWM_M1	GMAC1_MDC_M0	UART7_TX_M1	PDM_CLK1_M2
GPIO3_C5	SPDIF_TX_M1	PWM15_IR_M0	GMAC1_MDIO_M0	UART7_RX_M1	I2S1_LRCK_RX_M2

9.2.2. RS232 and RS485¶

RS232_1,RS232_2 and RS485 are respectively converted from UART2, UART3 and UART4 of the main control.The RS232_1 cannot be used directly because UART2 is used as debug serial port by default. If want to use RS232_1, you need to configure UART2 as a normal serial port.For relevant hardware connection and definition, you can refer ROC-RK3568-PC-SE schematic diagram. The following are some pins definition of RJ45 interface:

RJ45 PINS	Definition	RJ45 PINS	Definition
1	RS232_2 TX	5	GND
2	RS232_2 RX	6	RS232_1 RX
3	RS232_1 TX	7	RS485_A
4	GND	8	RS485_B

9.3. DTS configuration¶

Because UART2 is the debug serial port by default, the RS232_1 converted from UART2 cannot be used directly. We only need to configure in kernel/arch/arm64/boot/dts/rockchip/rk3568-firefly-roc-pc.dtsi:

RS232_2

the corresponding node /dev/ttyS3

&uart3 {
    status = "okay";
    pinctrl-0 = <&uart3m1_xfer>;
};

RS485

the corresponding node /dev/ttyS4

&uart4 {
    status = "okay";
    pinctrl-0 = <&uart4m1_xfer>;
};

UART7

the corresponding node /dev/ttyS7

&uart7 {
    status = "okay";
    pinctrl-0 = <&uart7m1_xfer>;
};

9.4. Debug method¶

Users can send and receive data to the serial port of the development board by using the USB to serial port adapter of different host according to different interfaces. For example, the debugging steps of RS485 are as follows:

(1) Connected hardware

Find the RJ45 interface with RS485 on the development board, and connect 5(GND), 7(A) and 8(B) pins of the RJ45 with GND, A and B pins of the host serial port adapter (USB to 485 to serial port module) respectively.

(2) Open the serial terminal of the host

Input the install Kermit command sudo apt install Kermit on the terminal. After the installation, open Kermit, set the baud rate and connect:

$ sudo kermit
C-Kermit> set line /dev/ttyUSB0
C-Kermit> set speed 9600
C-Kermit> set flow-control none
C-Kermit> connect

/dev/ttyUSB0 is the device file for USB to serial port adapter.

(3) Send data to host serial port adapter

The device file for RS485 is /dev/ttyS4. Run the following commands on the device:

echo firefly RS485 test... > /dev/ttyS4

The serial terminal in the host can receive a string: “firefly RS485 test… “

(4) Receive data from host serial port adapter

First run the following commands on the device:

cat /dev/ttyS4

Then enter a string at the host’s serial terminal: Firefly RS485 test..., the device side can see the same string.

(5) Exit kermit connection

The host hit keyboard ctrl+\ and then hit key c, input “exit” and hit enter

C-Kermit>exit
OK to exit? ok

9.5. How to configure UART2 as a normal serial port¶

In the public firmware, UART2 defaults to debug serial port. Next, take Android platform as an example to modify UART2 to normal serial port.

9.5.1. Kernel modification¶

Remove CONFIG_SERIAL_8250_CONSOLE configuration in kernel/arch/arm64/configs/firefly_defconfig

diff --git a/kernel/arch/arm64/configs/firefly_defconfig b/kernel/arch/arm64/configs/firefly_defconfig
index 57ed787..8d6bc18 100644
--- a/kernel/arch/arm64/configs/firefly_defconfig
+++ b/kernel/arch/arm64/configs/firefly_defconfig
@@ -500,7 +500,7 @@ CONFIG_INPUT_RK805_PWRKEY=y
 # CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_8250=y
 # CONFIG_SERIAL_8250_DEPRECATED_OPTIONS is not set
-CONFIG_SERIAL_8250_CONSOLE=y
+#CONFIG_SERIAL_8250_CONSOLE=y
 # CONFIG_SERIAL_8250_PCI is not set
 CONFIG_SERIAL_8250_NR_UARTS=10
 CONFIG_SERIAL_8250_RUNTIME_UARTS=10

Close the fiq-debugger node in kernel/arch/arm64/boot/dts/rockchip/rk3568-android.dtsi

diff --git a/kernel/arch/arm64/boot/dts/rockchip/rk3568-android.dtsi b/kernel/arch/arm64/boot/dts/rockchip/rk3568-android.dtsi
index 55a1716..0e297e6 100644
--- a/kernel/arch/arm64/boot/dts/rockchip/rk3568-android.dtsi
+++ b/kernel/arch/arm64/boot/dts/rockchip/rk3568-android.dtsi
@@ -26,7 +26,7 @@
                interrupts = <GIC_SPI 252 IRQ_TYPE_LEVEL_LOW>;
                pinctrl-names = "default";
                pinctrl-0 = <&uart2m0_xfer>;
-               status = "okay";
+               status = "disabled";
        };

        debug: debug@fd904000 {

Open UART2

diff --git a/kernel/arch/arm64/boot/dts/rockchip/rk3568-firefly-roc-pc.dtsi b/kernel/arch/arm64/boot/dts/rockchip/rk3568-firefly-roc-pc.dtsi
index f4af38a..fb9a3ff 100644
--- a/kernel/arch/arm64/boot/dts/rockchip/rk3568-firefly-roc-pc.dtsi
+++ b/kernel/arch/arm64/boot/dts/rockchip/rk3568-firefly-roc-pc.dtsi
@@ -137,6 +137,10 @@
        status = "okay";
 };

+&uart2 {
+       status = "okay";
+};
+

Recompile the kernel and upgrad it to the development board. After it takes effect, will generate /dev/ttyS2 node.