PWM Use

Introduction

AIO-3128C development board has 4 PWMs, namely PWM0 ~ PWM3:

• PWM0/GPIO0_D2: exported in the extension board

• PWM1/GPIO0_D3: used as AUX_DET signal internally

• PWM2/GPIO0_D4: used as RTC_INT signal internally

• PWM3: used by infrared transceivers

This chapter mainly describes how to configure PWM. The PWM driver of AIO-3128C is:

kernel/drivers/pwm/pwm-rockchip.c

Configuration steps

Configuration of PWM mainly includes the following three steps: configure PWM DTS nodes, configure PWM kernel driver, and control PWM device.

Create PWM DTS Node

The following PWM nodes are defined in kernel/arch/arm/boot/dts/rk312x.dtsi, as shown below:

pwm0: pwm@20050000 {
	compatible = "rockchip,rk-pwm";
	reg = <0x20050000 0x10>;
	#pwm-cells = <2>;
	pinctrl-names = "default";
	pinctrl-0 = <&pwm0_pin>;
	clocks = <&clk_gates7 10>;
	clock-names = "pclk_pwm";
	status = "disabled";
};

 pwm1: pwm@20050010 {
     compatible = "rockchip,rk-pwm";
     reg = <0x20050010 0x10>;
     #pwm-cells = <2>;
     pinctrl-names = "default";
     pinctrl-0 = <&pwm1_pin>;
     clocks = <&clk_gates7 10>;
     clock-names = "pclk_pwm";
     status = "disabled";
 };

 pwm2: pwm@20050020 {
      compatible = "rockchip,rk-pwm";
      reg = <0x20050020 0x10>;
      #pwm-cells = <2>;
      pinctrl-names = "default";
      pinctrl-0 = <&pwm2_pin>;
      clocks = <&clk_gates7 10>;
      clock-names = "pclk_pwm";
      status = "disabled";
 };

 pwm3: pwm@20050030 {
       compatible = "rockchip,rk-pwm";
       reg = <0x20050030 0x10>;
       #pwm-cells = <2>;
       pinctrl-names = "default";
       pinctrl-0 = <&pwm3_pin>;
       clocks = <&clk_gates7 10>;
       clock-names = "pclk_pwm";
       status = "disabled";
 };

To use PWM0, you need to add to file kernel/arch/arm/boot/dts/aio-3128c.dts:

&pwm0 {
       status = "okay";
};

Configure PWM kernel driver

PWM driver is located on the file kernel/drivers/pwm/pwm-rockchip.c.

Control PWM Device

The user can use the PWM node generated from the above steps in the other driver file. The specific methods are as follows:

(1). Include the following header file into the device driver files to be controlled by PWM:

#include <linux/pwm.h>

This header file mainly includes PWM function interface.

(2). Request for PWM

You can use the pwm_request function to request the PWM device. For example:

struct pwm_device * pwm0=NULL;pwm0= pwm_request(0, “backlight-pwm”);

See The API of PWM device for more detail of this function.

(3). Configure PWM

You can use the function pwm_config to set the PWM configuration. For example:

pwm_config(pwm0, 500000, 1000000)；

See The API of PWM device for more detail of this function.

(4). PWM enabling function

Then you start the pwm device using the pwm_enable function. For example：

int pwm_enable(struct pwm_device *pwm);

See The API of PWM device for more detail of this function.

The API of PWM device

/**
 * pwm_request() - request a PWM device
 * @pwm_id: global PWM device index
 * @label: PWM device label
 *
 * This function is deprecated, use pwm_get() instead.
 */
 struct pwm_device *pwm_request(int pwm_id, const char *label);


/**
 * pwm_free() - free a PWM device
 * @pwm: PWM device
 *
 * This function is deprecated, use pwm_put() instead.
 */
 void pwm_free(struct pwm_device *pwm);


/**
 * pwm_config() - change a PWM device configuration
 * @pwm: PWM device
 * @duty_ns: "on" time (in nanoseconds)
 * @period_ns: duration (in nanoseconds) of one cycle
 */
 int pwm_config(struct pwm_device *pwm, int duty_ns, int period_ns);


/**
 * pwm_enable() - start a PWM output toggling
 * @pwm: PWM device
 */
 int pwm_enable(struct pwm_device *pwm);


/**
 * pwm_disable() - stop a PWM output toggling
 * @pwm: PWM device
 */
 void pwm_disable(struct pwm_device *pwm);