UART

Introduction

AIO-3568J supports UART、RS232、RS485 interfaces

UARTx2

RS485x2

RS232x2

The RS232 of the board is extended from RK3568 uart3 and uart4,
whereas the interfaces UART and RS485 of the board are extended from
SPI bridge/extension chip WK2124.

SPI bridge/extension chip WK2124 with functions of four enhanced
serial ports (UART), among them:

the baud rate, word length and check format of each subchannel UART
can be set independently, and the maximum communication rate of 2Mbps
can be provided

each sub-channel has 256 BYTE FIFO, which can be programmed according
to user requirements.

has a subserial port to receive FIFO timeout interrupts.

supports start bit error detection.

The serial interface diagram of the AIO-3568J development board is as
follows:


DTS configuration

File "kernel/arch/arm64/boot/dts/rockchip/rk3568-firefly-port.dtsi"
has the definition of spi to uart related nodes:

   &spi1 {
           status = "disabled";
           max-freq = <48000000>;
           dev-port = <0>;
           pinctrl-0 = <&spi1m1_pins>;
           pinctrl-1 = <&spi1m1_pins_hs>;

           spi_wk2xxx: spi_wk2xxx@00{
                   status = "disabled";
                   compatible = "firefly,spi-wk2xxx";
                   reg = <0x00>;
                   spi-max-frequency = <10000000>;
                   power-gpio = <&pca9555 PCA_IO1_7 GPIO_ACTIVE_HIGH>;
                   reset-gpio = <&pca9555 PCA_IO1_1 GPIO_ACTIVE_HIGH>;
                   irq-gpio = <&gpio0 RK_PA6 IRQ_TYPE_EDGE_FALLING>;
                   cs-gpio = <&gpio3 RK_PA1 GPIO_ACTIVE_HIGH>;
           };
   };

As you can see, enabling the node in the
"kernel/arch/arm64/boot/dts/rockchip/firefly-rk3568-aioj.dtsi" file is
available. In addition, SPI1 node needs to be enabled because SPI to
UART serial port module used by our board is attached to SPI1. As
follows:

   &uart3 {
           status = "okay";
   };

   &uart4 {
           status = "okay";
   };

   &spi1 {
           status = "okay";
   };

   &spi_wk2xxx {
           status = "okay";
   };

After the serial port is configured, the nodes on the hardware
interface corresponding to the software are:

   RS485_1：  /dev/ttysWK0
   RS485_2：  /dev/ttysWK1
   UART1：    /dev/ttysWK2
   UART2：    /dev/ttysWK3
   RS232_1 :  /dev/ttyS3
   RS232_2:   /dev/ttyS4

PINs Definition

RS232

RS485

UART

Debug method

Users can send and receive data to the serial port of the development
board by using the USB to serial port adapter of different host
according to different interfaces. For example, the debugging steps of
RS485 are as follows:

(1) Connected hardware

Connect A, B and GND pins of development board RS485 with A, B and GND
pins of host serial port adapter (USB to 485 to serial port module)
respectively.

(2) Open the serial terminal of the host

Input the install Kermit command "sudo apt install Kermit" on the
terminal. After the installation, open Kermit, set the baud rate and
connect:

   $ sudo kermit
   C-Kermit> set line /dev/ttyUSB0
   C-Kermit> set speed 9600
   C-Kermit> set flow-control none
   C-Kermit> connect

/dev/ttyUSB0 is the device file for USB to serial port adapter.

(3) Send data to host serial port adapter

The device file for RS485 is "/dev/ttysWK0". Run the following
commands on the device:

   echo firefly RS485 test... > /dev/ttysWK0

The serial terminal in the host can receive a string: "firefly RS485
test... "

(4) Receive data from host serial port adapter

First run the following commands on the device:

   cat /dev/ttysWK0

Then enter a string at the host's serial terminal: "Firefly RS485
test...", the device side can see the same string.

(5) Exit kermit connection

The host hit keyboard "ctrl+\" and then hit key c, input "exit" and
hit enter

   C-Kermit>exit
   OK to exit? ok