UART

Introduction

AIO-1126-JD4 supports  UART6,UART7 to RS485. UART3,UART4 interfaces to
RS232.

DTS Configuration

File path: "kernel-6.1/arch/arm64/boot/dts/rockchip/rv1126b-firefly-
aio-1126bjd4.dtsi"

   #ifdef FF_RS485_1
   &uart6{
   	pinctrl-names = "default";
   	pinctrl-0 = <&uart6m0_xfer_pins>;
   	status = "okay";
   };
   #endif

   #ifdef FF_RS485_2
   &uart7{
   	pinctrl-names = "default";
   	pinctrl-0 = <&uart7m0_xfer_pins>;
   	status = "okay";
   };
   #endif

   #ifdef FF_RS232_1
   &uart3 {
   	pinctrl-0 = <&uart3m1_xfer_pins>;
   	status = "okay";
   };
   #endif

   #ifdef FF_RS232_2
   &uart4 {
   	pinctrl-0 = <&uart4m1_xfer_pins>;
   	status = "okay";
   };
   #endif

   #ifdef FF_UART5
   &uart5{
   	status = "okay";
   	pinctrl-0 = <&uart5m1_xfer_pins>;
   };
   #endif

After configuring the serial port, the nodes corresponding to the
hardware interface on the software are:

   UART6:  /dev/ttyS6        RS485_1
   UART7:  /dev/ttyS7        RS485_2
   UART3:  /dev/ttyS3        RS232_1
   UART4:  /dev/ttyS4        RS232_2
   UART5:  /dev/ttyS5

Send And Receive Verification

Users can use different host USB to serial port adapters to send and
receive data to the serial port of the development board according to
different interfaces. For example, the debugging steps of UART3 are as
follows:

(1) Development board sends, host receives

   # Host terminal executes first:
   # /dev/ttyUSB0 is the node of host serial port adapter, modify according to actual situation
   cat /dev/ttyUSB0

   # Development board debug serial port terminal executes:
   # /dev/ttyS3 is UART3 node
   echo "firefly UART3 test..." > /dev/ttyS3

The host terminal can receive the string "firefly UART3 test..."

(2) Host sends, development board receives

   # Development board debug serial port terminal executes first:
   # /dev/ttyS3 is UART3 node
   busybox  stty -echo -F /dev/ttyS3       # Turn off echo
   cat /dev/ttyS3

   # Host terminal execution:
   # /dev/ttyUSB0 is the node of the host serial port adapter, modify according to the actual situation
   echo "firefly UART3 test..." > /dev/ttyUSB0

The development board debugging serial port terminal can receive the
string "firefly UART3 test..."

RS485

GPIO5_B3 and GPIO5_B6 are used as control transceiver pins for RS485_1
and RS485_2 respectively. The pin is set to transmit when pulled high
and to receive when pulled low. Users can operate it through the
/sys/class/gpiosubsystem.

Configure GPIO5_B3(RS485_1) as output.

   echo 171 > /sys/class/gpio/export
   echo out > /sys/class/gpio/gpio171/direction

Pull GPIO5_B3 high for RS485 transmission: echo 1 >
/sys/class/gpio/gpio171/value

Pull GPIO5_B3 low for RS485 reception: echo 0 >
/sys/class/gpio/gpio171/value

Configure GPIO5_B6(RS485_2) as output.

   echo 174 > /sys/class/gpio/export
   echo out > /sys/class/gpio/gpio174/direction

Pull GPIO5_B6 high for RS485 transmission: echo 1 >
/sys/class/gpio/gpio174/value

Pull GPIO5_B6 low for RS485 reception: echo 0 >
/sys/class/gpio/gpio174/value