Serial port debugging

Notes

The serial port for debugging and the TF card interface of Firefly-
PX3-SE development board share the same signal pins, so you cannot use
them at the same time.

Therefore, if you want to use the debug serial port, you need to pull
out the TF card, and if you want to use TF card, please do not connect
to the debug serial port.

Adapter selecion

There are many USB-to-serial adapters on online stores. According to
the chips difference, we can devided them as:

PL2303

CH340

Generally, adapter equipped with CH340 chip has a more stable
performance and thus a higher price.

Hardware connection

Serial to USB adapter with four different color cables:

Red: 3.3V power supply, you don't need to connect it to the
development board.

Black: GND, the GND cable of the serial port. Please connect it to the
GND pin of the serial port on the development board.

White: TXD, the output cable of the serial port. Please connect it to
the TX pin of the serial port on the development board.

Greem: RXD, the input cable of the serial port. Please connect it to
the RX pin of the serial port on the development board.

Parameters for connection

Firefly-PX3-SE uses the following serial port parameters:

baud rate: 115200

data bits: 8

stop bit: 1

ddd-even check: None

flow control: None

Serial port debugging on Windows

Install driver

Download the driver and install it:

CH340

PL2303

If you cannot use PL2303 in Win8 normally, please refer to

This article

 and use an older version driver such as version 3.3.5.122 or lower.

Once you connect the adapter to your computer, the system will tell
you that a new hardware is added and the system will initialize it.
Afte that, you will find the corresponding COM interface in the device
manager.

Install software

Generally, we use putty or SecureCRT tool on windows. Putty is an open
source tool and we will introduce it here. SecureCRT usage is similar
to Putty.

Go to

Download putty

 and we recommend you to download "putty.zip", because it contains
other useful tools.

Decompress the package and run PUTTY.exe. Choose the Connection type
as Serial, set the Serial line as the newly added COM interface you
find in the device manager and set the Speed Baud rate as 115200, and
then click Open:


Serial port debugging on Ubuntu

There are many choices on Ubuntu:

picocom

minicom

kermit

It is easy to use picocom. We will introduce this tool in the
following part and other softwares are similar to it.

Install

   sudo apt-get install picocom

If you have connected the serial port to the computer successfully,
please check the serial port devices. For example, if the device name
is ttyUSB0, you can use the following command to find it:

   $ ls /dev/ttyUSB*
   /dev/ttyUSB0

Run

   $ picocom -b 115200 /dev/ttyUSB0
   picocom v1.7

   port is        : /dev/ttyUSB0
   flowcontrol    : none
   baudrate is    : 115200
   parity is      : none
   databits are   : 8
   escape is      : C-a
   local echo is  : no
   noinit is      : no
   noreset is     : no
   nolock is      : no
   send_cmd is    : sz -vv
   receive_cmd is : rz -vv
   imap is        : 
   omap is        : 
   emap is        : crcrlf,delbs,

   Terminal ready

You will find in the above code that "Ctrl-a" is a escape charater. If
you want to quit the terminal, just press "Ctrl-a" and "Ctrl-q". In
addition, there are some other frequently used control commands:

Ctrl-u : increase the Baud rate

Ctrl-d : lower the Baud rate

Ctrl-f : Switch among different flow control settings(hardware flow
control technology RTS/CTS, software flow control technology XON/XOFF,
no flow control）

Ctrl-y : Switch among odd-even check (even, odd, none)

Ctrl-b : Switch among data bits (5, 6, 7, 8)

Ctrl-c : Switch for backing to local-echo

Ctrl-v : Display the current serial port parameters and status